Difference between revisions of "Formulae"

Revision as of 13:59, 14 July 2009

This page will contain all the various formulae found in the game. Those formulae dictate how the game works and have been proven through various means.

Buff boosts

Buffs give the following boost to your attributes:

Type	Attr.	LV1	LV2	LV3	LV4	LV5
	ATP	111%	115%	119%	123%	127%
	ATA
	DFP
	TP

Those values are not confirmed and are likely only approximations.

Physical damage formula

First you have to calculate your total ATP:

atp = character's atp + line shield's atp + unit's atp + weapon's atp

Then get your PA modifier value correctly. It's a percent, therefore:

pa = pa modifier / 100

You can get the buff boost for ATP by looking at the above table and dividing by 100. If you used an agtaride, then buff = 1.15.

To determine the elemental modifier you must first ask yourself whether you attack with the correct element. If you attack with neutral, or an element different than the enemy's element or its opposite element, then ele = 0. Otherwise, apply the following formula to obtain the element modifier:

ele = (5 + element's %) / 151.5

If you used the same element as the enemy then multiply ele by -1.

If the hit is critical then crit = 1.5, otherwise crit = 1.

You can find the enemy's DFP by first looking at the enemies' page and then multiplying that DFP by the modifier found on each enemy's page.

Knowing all those variables, you can now calculate the physical damage you will do:

maximum damage = floor(crit x (atp x pa x (1 + ele) x buff - enemy's dfp) / 5)

You can find more information about the floor function at Wikipedia.

This value is the maximum damage you can make in these settings. To obtain the complete damage range your weapon can make you must apply the variance.

TECHNICs damage formula

This formula works pretty much like the above formula, with a few exceptions. For the sake of convenience only the exceptions will be listed.

Instead of ATP you have TP, but you calculate the total TP in the same way:

tp = character's tp + line shield's tp + unit's tp + weapon's tp

The element modifier's calculation is different. TECHNICs get a lot of boost on this point, so using the correct element is really important. If you use the wrong element then ele = 0. Otherwise it is dependent on the weapon's elemental percent and the PA level you're using:

ele = (14 + element's % + PA's level) / 151.5

If you used the same element as the enemy then multiply ele by -1.

If you use a rod then you get a boost and rod = 1.2. Otherwise rod = 1.

You also need to know the PA modifier, buff boost (this time for TP) and critical value, defined above.

The resulting formula is:

maximum damage = floor(crit x (rod x tp x pa x (1 + ele) x buff - enemy's mst) / 5)

This value is the maximum damage you can make in these settings. To obtain the complete damage range your weapon can make you must apply the variance.

Variance

A weapon's damage have a minimal and maximal value. The variance exists because every weapon in the game have a high ATP value (shown in its stats) and low ATP value (invisible). The low ATP value is obtained by substracting the variance from the high ATP value. The variance do not change between grinds, only between weapons. The variance cannot cause the weapon ATP to reach below 1.

low ATP value = high ATP value - variance

If you know the low ATP value of a weapon you can calculate its minimum damage by applying the above formula and replacing the weapon ATP by its lower ATP.

The actual damage on the other hand is a random number between the minimum and maximum values, obtained through this formula:

actual damage = random(minimum damage, maximum damage)

with random(x, y) = a random number between x and y included.

Hit rate formula

First you need to be aware that TECHNICs never miss. If you're not using a TECHNIC, proceed with the formula.

You need to know the enemy's EVP. You can find it by first looking at the enemies' page and then multiplying that EVP by the modifier found on each enemy's page.

Then you need to calculate your total ATA which is:

ata = character's ata + line shield's ata + unit's ata + weapon's ata

Then get your PA modifier value correctly. Make sure to use the value for accuracy. It's a percent, therefore:

pa = pa modifier / 100

The resulting hit rate can be calculated with this simple formula:

hit rate = 1 - enemy's evp / (ata x pa modifier x 10)

You can multiply this result by 100 to obtain a percent value.